如何利用化學法生產磨砂u玻璃的方法
用化學法出產磨砂玻璃的工藝辦法，其過程是：
（1）清洗烘干：主要對要將出產磨砂玻璃的平板玻璃用水進行清洗，去除灰塵、污漬，然后烘干；
?。?）吊裝：將清洗烘干后的平板玻璃裝入吊裝架上，吊裝架與玻璃相接觸的部分用齒形橡膠支架墊起，是立式排放，玻璃與玻璃之間相距一定的距離，用吊車吊起；
?。?）腐蝕：用吊車將平板玻璃連同吊裝架一同浸入腐蝕箱中，選用慣例腐蝕液浸沒玻璃，腐蝕時刻5-10分鐘，用吊車吊起后，淋掉殘液；
?。?）軟化：淋掉殘液后，磨砂玻璃上面附著一層殘留物，放入軟化箱中軟化，選用慣例軟化液浸沒玻璃，軟化時刻1－2分鐘，去掉殘留物；
?。?）清洗：因?yàn)楦g與軟化使磨砂玻璃體帶有許多化學物質，所以有必要清洗，把磨砂u型玻璃設計把玻璃放入沖洗機的滑道上，滑道帶動磨砂玻璃進入清洗機，清洗機一邊噴入清水，一邊轉動毛刷，當磨砂玻璃被清洗機滑道帶出清洗機后，磨砂玻璃清洗完畢；
（6）清洗后的磨砂玻璃放入烘干室烘干，即成單面或雙面磨砂玻璃。
磨砂玻璃表面粗糙，使光線產生漫反射透光而不透視：光線通過磨砂玻璃被反射后向四面八方射出去在（因?yàn)槟ド安ＡП砻娌皇枪饣钠矫?，使光產生了漫反射），折射到視網膜上已經是不完整的像，于是就看不見玻璃背后的東西了。它可以使室內光線柔和而不刺目。
The process of producing frosted glass by chemical method is as follows: (1) cleaning and drying: cleaning the flat glass with water, removing dust and stains, and then drying; (2) lifting: the cleaned and dried flat glass is put into the lifting frame. The part of the lifting frame that comes into contact with the glass is supported by a toothed rubber support, which is vertical drainage. The distance between the glass and the glass is a certain distance, and is lifted by a crane; (3) corrosion: The flat glass is immersed into the corrosion box together with the lifting frame by a crane, and the glass is immersed in the conventional corrosion solution for 5-10 minutes, after lifting by a crane, the residual liquid is leached off; (4) softening: After the residual liquid is leached off, frosted glass with a layer of residue attached to the top, put into the softening box to soften, choose the usual softening solution to soak the glass, softening time 1-2 minutes, remove the residue; (5) cleaning: Because of corrosion and softening of the frosted glass body with a lot of chemicals, so it is necessary to clean, put the frosted u glass design glass into the washing machine on the slide, slide drive frosted glass into the washing machine, when the frosted glass is taken out of the washing machine, the frosted glass is cleaned; (6) the frosted glass after cleaning is put into the drying room to dry, that is to say, the frosted glass becomes single side or double side frosted glass. The surface of frosted glass is rough, so that light is diffused without penetration: light is reflected through frosted glass and then shot out in all directions (because frosted glass is not a smooth surface, so that light is diffused) , refracted on the Retina is an incomplete image, so you can't see what's behind the glass. It can make indoor light soft and not harsh.